If you’re preparing for a Work Permit Receiver (WPR) test, practicing the right MCQs can make your preparation stronger and more effective. In industries like Saudi Aramco, SABIC, and other oil & gas or construction projects, the WPR role is critical because it ensures that all work activities are carried out safely according to permit conditions, hazard controls, and company safety standards.
To help you pass your WPR 3rd Party exam, Saudi Aramco WPR exam, and contractor safety assessments with confidence, we have compiled 50 important Work Permit Receiver (WPR) MCQs with answers. These questions cover key topics such as permit types, issuer and receiver responsibilities, JSA review, gas testing requirements, confined space permits, hot work permits, renewal and closure procedures, and emergency actions everything you need to perform well in exams, interviews, and on-site evaluations.
Table of Contents
Work Permit Receiver – Saudi Aramco WPR Exam MCQs Questions
1. When work involves other departments or known/suspected underground utilities within battery limits, who is responsible for obtaining the countersignature from the affected department/issuer?
- Maintenance personnel
- Issuer
- Designated representative
- Receiver
Correct Answer : Receiver
2. When a permit is renewed, what must be done if it contains a countersignature from another organization/department?
- Notify all countersigning organizations about the permit renewal
- Obtain countersignatures again upon renewal
- No need to inform or take countersign again
- Inform shift supervisor
Correct Answer : Obtain countersignatures again upon renewal
3. Who must sign the work permit to close it?
- Gas Tester, Issuer and Receiver
- Designated Representative
- Competent person
- Both the issuer and receiver
Correct Answer : Both the issuer and receiver
4. Why must a work permit be closed?
- To allow a gas test to be taken
- To make sure the work site is left in a safe condition
- To stop work
- To communicate the status of work
Correct Answer : To make sure the work site is left in a safe condition
5. When must a work permit be closed?
- When work will finish
- When workers are going to camp
- Not required to close
- Just before the end of shift
Correct Answer : When work will finish
6. When must the work permit be closed?
- After a gas test is taken
- When the issuer leaves the job site
- When the work is finished and/or the work crew leaves
- Before another permit is issued
Correct Answer : When the work is finished and/or the work crew leaves
7. Why is the checklist section important to the Issuer and Receiver?
- It controls the Receiver’s break time
- It tells them all the precautions to take
- It defines the duration and scope of work
- It makes sure that important steps have been taken
Correct Answer : It makes sure that important steps have been taken
8. “Use a fire blanket” and “hand dig only” are examples of what?
- Not safety precautions
- Working criteria
- Additional precautions
- Basic safety
Correct Answer : Additional precautions
9. What information does the “Exact Work Location” (or “Work Location Box”) provide?
- Up to which time the Receiver can work
- What equipment can be used
- How many workers can be on site
- Where the Receiver can work
Correct Answer : Where the Receiver can work
10. What information does the “Location Box” on a work permit provide to the Receiver?
- Exact equipment which the Receiver can use
- None of the above
- Where the Receiver can go
- Exact location where the Receiver can work
Correct Answer : Exact location where the Receiver can work
11. What information does the “Duration Box” on a work permit give to the Receiver?
- When to start and when to stop work
- Where the Receiver can work
- How many workers are allowed for work
- Up to which time the Receiver can work
Correct Answer : When to start and when to stop work
12. If a work permit is not issued during an emergency, what must be done to perform the work?
- Superintendent must approve
- All safety precautions must be taken
- Wear SCUBA and perform work
- Perform joint site inspection
Correct Answer : All safety precautions must be taken
13. A work permit must be written in:
- English
- Arabic
- Ink pen
- Arabic and lead pencil
Correct Answer : English
14. The Issuer must stop work if:
- The Issuer left the job site
- The Issuer lost his copy of the permit
- When the Issuer goes to his office
- The job site is found to be unsafe
Correct Answer : The job site is found to be unsafe
15. What must the Issuer do after he stops work?
- Give his copy to the Receiver
- Close, then extend the permit
- Get a countersign
- Write the reason on the permit
Correct Answer : Write the reason on the permit
16. When must the Receiver stop work?
- He cannot find the Issuer
- The work site becomes unsafe
- The Issuer leaves the job site
- The designated representative must leave
Correct Answer : The work site becomes unsafe
17. What must the Receiver do if he stops work?
- Inform the Issuer
- Tell the senior craftsman
- Tell his immediate supervisor
- Tell the designated representative
Correct Answer : Inform the Issuer
18. What would be a good example of when a Receiver must stop work?
- He hears an emergency alarm
- He cannot wait for the countersign
- The backhoe runs out of fuel
- Material has not yet arrived
Correct Answer : He hears an emergency alarm
19. When a safety problem arises at the work site and the Receiver does not stop work, what might happen?
- A fire, injury, or accident can occur
- An accident can occur
- Countersignature becomes void
- The work permit expires
Correct Answer : A fire, injury, or accident can occur
20. Where will you find Stop Work Authority (SWA)?
- CSM only
- In Stop Work G.I
- CSM, SMS, Safety Handbook
- Can download from Internet
Correct Answer : CSM, SMS, Safety Handbook
21. In Saudi Aramco, who can stop unsafe work?
- All personnel / Everyone
- Receiver and Issuer
- Designated representative
- Proponent manager
Correct Answer : All personnel / Everyone
22. In the Saudi Aramco Stop Work Authority (SWA) procedure, how many steps are there?
- Five
- Only three steps
- Too many steps
- As many as required by the Issuer
Correct Answer : Five
23. Which sequence is correct for the Stop Work Authority (SWA) steps in Saudi Aramco?
- Stop, notify, investigate, follow-up, communicate
- Stop, communicate, notify, investigate, follow-up
- Communicate, investigate, stop, follow-up
- Stop, notify, investigate, communicate, follow-up
Correct Answer : Stop, notify, investigate, communicate, follow-up
24. Select the steps of Saudi Aramco Stop Work Authority (SWA)
- Communication
- Make Safety Alert
- Notify all persons
- Stop unsafe work
- Investigate
- Follow up
Correct Answer : Communication, Notify all persons, Stop unsafe work, Investigate, Follow up
25. In Saudi Aramco facility areas, where can anyone get help regarding safety and work procedures?
- Daily news bulletin
- Loss Prevention monthly magazine
- Only from CSM
- CSM, SMS, Safety Handbook
Correct Answer : CSM, SMS, Safety Handbook
26. What is the difference between hot work and cold work?
- Both use an ignition source
- Neither uses an ignition source
- Cold work uses an ignition source
- Hot work involves/uses an ignition source, while cold work does not involve an ignition source
Correct Answer : Hot work involves/uses an ignition source, while cold work does not involve an ignition source
27. Cold work includes:
- Scaffold erection and using a backhoe
- Carpentry work and brush painting
- Abrasive blasting and painting
- Sand removal and scaffold erection
Correct Answer : Sand removal and scaffold erection, Scaffold erection and using a backhoe, Abrasive blasting and painting, Carpentry work and brush painting
28. When is an Equipment Opening / Line Break permit required?
- When an operator purges an equipment
- When an operator releases hydrocarbon to flare
- When craftsmen build a scaffold
- When a pipefitter opens a line or installs a blind
Correct Answer : When a pipefitter opens a line or installs a blind
29. What should be checked before allowing entry into a confined space?
- Lighting, standby man, and air mover (ventilation)
- Air mover, respirator, and countersignature
- Fire watch, standby man, and gas test
- Gas test, fire watch, and barricade
Correct Answer : Fire watch, standby man, and gas test
30. What are the minimum checks required before issuing an equipment opening / line break permit (e.g., before opening a pipe flange joint)?
- Sewer, manway, and air mover
- Safety harness, belt, and safety glasses
- Wind direction, draining, and ignition source
- Ignition source, gloves, and safety glasses
Correct Answer : Wind direction, draining, and ignition source
31. If one welding machine is to be used by a welding group and an electrical group performing tasks of different nature, how many work permits are required?
- Two work permits
- One permit if the Issuer agrees
- Three
- One
Correct Answer : Two work permits
32. When going into a manhole to perform a welding job, what permits are required?
- Cold work and confined space entry permit
- Confined space entry permit only
- Hot work and confined space entry permit
- Hot and cold work permit
Correct Answer : Hot work and confined space entry permit
33. When working for well head tie in job using crane and hand tools, what kind of permits are required?
- Hot work, cold work, and equipment opening / line break permit
- Equipment opening/line break permit
- Hot work and cold work permits
- Hot work and confined space entry permit
Correct Answer : Hot work, cold work, and equipment opening / line break permit
34. With manual back filling, a crew need, engine operated compactor to do their job in 5 ft deep trench (excavation), what kind of permits are required?
- Only confined space entry permit
- Hot work and cold work
- Hot work, cold work, and confined space entry permit
- Cold work and confined space entry permit
Correct Answer : Cold work and confined space entry permit
35. For electric operated X-ray equipment (industrial radiography), what type of work permit is required?
- Confined space entry permit
- Hot work permit
- Cold work permit
- No permit is required
Correct Answer : Cold work permit
36. What type of work permit is required for industrial radiographic testing (RT) using a sealed gamma radiation source?
- Equipment opening/line break permit
- Hot work permit
- Cold work permit
- No permit is required
Correct Answer : Cold work permit
37. The use of an internal combustion engine (e.g., air compressor) in a restricted area requires which type of work permit?
- Hot work permit
- Equipment opening/line break permit
- Cold work permit
- Confined space entry permit
Correct Answer : Hot work permit
38. A pipefitter cannot work on the same piece of equipment using a welder’s work permit because:
- Gas testing is not required for a pipefitter’s work
- Welders are usually contractors
- Each type of work involves different hazards
- Joint site inspection is not required for a pipefitter’s job
Correct Answer : Each type of work involves different hazards
39. Can work in two different locations, or two activities of different natures, be performed under one work permit?
- Only with superintendent approval
- Yes
- No
- Only if agreed by the Issuer
Correct Answer : No
40. If mechanical and electrical groups are working on the same equipment in a restricted area, how many work permits are required?
- Each group must have its own separate work permit
- When the foreman and superintendent agree on one work permit
- When the maintenance person agrees to work without a permit
- Two work permits are required
Correct Answer : Each group must have its own separate work permit
41. When performing cleaning (e.g., tank cleaning from inside), internal inspection, or work inside sewers, which type(s) of work permit is/are required?
- Hot / Cold and confined space entry permit
- Cold work permit
- Equipment opening/line break permit
- Hot and cold work permit
Correct Answer : Hot / Cold and confined space entry permit
42. If a driver wants to take a vehicle or construction equipment inside a restricted area, what type of work permit is required?
- Vehicle entry permit
- Confined space entry permit
- Cold work permit
- Hot work permit
Correct Answer : Hot work permit
43. What type of work permit is required when working in close proximity to a live electrical line or near electrically energized equipment?
- Cold work permit
- Hot work permit
- Equipment opening/line break permit
- Hot work and confined space entry permit
Correct Answer : Hot work permit
44. Abrasive blasting (sand blasting) in a restricted area requires which type of work permit?
- Hot work permit
- Equipment opening/line break permit
- Cold work permit
- Hot work and confined space entry permit
Correct Answer : Hot work permit
45. For an abrasive blasting (sand blasting) job on a scaffold, what load rating is required?
- Very light duty
- Any duty of scaffold
- Light duty
- Medium duty
Correct Answer : Medium duty
46. What should the Issuer check before issuing a work permit for crane lifting operations?
- Physical condition of lifting gears
- Crane’s checklist
- Certificate of operator and rigger
- All of the above
Correct Answer : All of the above
47. At what depth of an excavation or trench does a Confined Space Entry permit become required?
- 2.2 meters
- 1.2 feet
- 4 feet
- 4 meters
Correct Answer : 4 feet
48. What is the required minimum distance for a scaffold base from the edge of an excavation?
- 1.5 × depth of excavation
- 1 meter
- 2.6 meters
- Height of scaffold × depth of excavation
Correct Answer : 1.5 × depth of excavation
49. What is the minimum distance that motor vehicles and heavy equipment must be kept from the edge of an excavation?
- 3 meters (10 ft)
- 1.5 × depth of excavation
- 2 meters (6.5 ft) or the depth of excavation
- 1.8 meters (6 ft)
Correct Answer : 2 meters (6.5 ft) or the depth of excavation
50. Which equipment are exempted from the 2-meter distance rule and allowed to operate within 2 meters of an excavation edge?
- Crane
- Welding truck
- Excavation and backfilling equipment
- None of the above
Correct Answer : Excavation and backfilling equipment